Bitumen Roofing Felt Adhesive - Black Jack - 5 Litres

4.8

(402)

Write Review

$ 14.00

Add to Cart

Qty

In stock

Description

From Everbuild, this Black Jack Roofing Felt Adhesive is a black oxidised bitumen-based cold felt roofing adhesive that is cold applied. It is perfect for b
From Everbuild, this Black Jack Roofing Felt Adhesive is a black oxidised bitumen-based cold felt roofing adhesive that is cold applied. It is perfect for bonding roofing or glueing roofing felt to itself, concrete, asphalt, metal, wood and comparable surfaces. It also makes a cold gritting solution.The recommended felt laying techniques should comply with BS 8217-1994. The most effective way of applying the Black Jack Roof Felt Adhesive is by brush or mop. Leave it open for 15 to 30 minutes before placing the roofing felt into the wet adhesive film. Be careful while placing the felt and rub or roll each section to ensure maximum contact with the adhesive while excluding air. The felt should be weighted down until it is fully adhered to. Where possible, unroll the felt into the adhesive and roll it with a lighter roller (around 25kg).Features & Benefits: Bitumen Roofing Felt Adhesive - Black Jack - 5 LitresExcellent high bond strengthIdeal as a roof felt glue for bonding all roofing felts to metal, concrete, roofing felt and woodAlso suitable for grittingMakes a good shed felt adhesive and can seal roofing felt lapsBonds chippings to the final layer of feltStorage life of 24 months in sealed and undamaged containersWhen using lap cement, the laps at the edges should be at least 75mm wide, while the laps at roll ends should be 150mm. Ensure that you treat the final edges and laps generously on their underside with Black Jack Roof Felt Adhesive and compact them well. If you're working on a timber roof structure, nail down the first felt layer to meet the standards of BS 8217-1994. You can also bond the second and third layers using Black Jack Roof Felt Adhesive. If you're working on concrete or lightweight concrete screeds, you must prime porous surfaces to ensure successful adhesion to Black Jack Roof Felt Adhesive. Use Black Jack Bitumen and Flashing Primer and make sure it's fully dried before applying the first layer of felt.As a solution for cold gritting, Black Jack Roof Felt Adhesive can be used on roofs with a slope of 10°. It is important to make sure that the surface is clean, free from dirt, dust, debris and dry. The felt adhesive can be applied to damp surfaces, but not to wet or waterlogged surfaces. It should be spread evenly directly from the container in areas of 20m² at a time., and the film should not be allowed to puddle or become too thin. Chippings should be applied immediately into the wet film, but take care not to over-chip. Ensure that the chippings cover the film from shoulder to shoulder. Excess chippings should be brushed from the completed surface after 72 hours. It is important not to leave the black film exposed.Please note: Before applying, surfaces should be repaired, dry and clean, as well as free from loose debris, dirt, grease and rust. A stiff-bristled brush should remove algae and fungus growth, then areas can be treated with Everbuild Fungicidal Wash to kill spores and prevent regrowth. Porous surfaces can be primed with a coat of Black Jack Bitumen Primer.After 24 hours, check all bonding for full adhesion. Make sure to check all laps and if in doubt, press home or roll any felt that lacks adhesion.Tools can be cleaned with paraffin or white spirit and spills should be wiped clean before the felt adhesive is set.Do not use in places where subsequent solvent contact is likely. Avoid inhalation of vapours in tight spaces. Nail down the first felt layer on timber roof structures to meet BS 8217-1994.Black Jack Roof Felt Adhesive contains a flammable solvent. Normal fire precautions must be taken during storage and use. Store in the original container in cool dry conditions and keep clear of sources of ignition.